Browse by products

Browse by products

EXPTC010GEx-proof P&T motor with housing for thermal imaging cameras

Config link




The Pan & Tilt unit EXPTC010G is made with strong Anticorodal aluminium, die-cast alloy of AISi 7Mg EN - AB 42000 group. EXPTC010G is equipped with a germanium viewing window designed for thermal imaging camera installations. The germanium window composition has remarkable properties and covers transmission from 7.5 to 14μm IR range with the best optical quality. All external components are stove enamelled.

The system includes a housing with the same characteristics of the EXHC000G and a Pan & Tilt, designed for movement both horizontally and vertically. The peculiar characteristic of the device is the absence of external wiring in rotation, either for the control of the Pan & Tilt or for the camera and lens. This solution makes the installation and the maintenance of the Pan & Tilt easy. One multi-conductor cable comes out from the base of the Pan & Tilt through a cable-gland. The EXPTC010G is supplied with preset, auto-pan and housing heater and optional sunshield.

The P&T functions are controlled by the EXDTRX telemetry receiver..


Designed to meet the strictest international standards and to operate in hazardous areas

For thermal cameras

Solid, non corrosive die-cast aluminium construction

The housing can accomodate most thermal cameras and lens combination

Housing heater and autopan

Not to be installed upside down


  • Non-corrosive die-cast aluminium (anticorodal)
  • Epoxy powder painted with orange peel effect, RAL7032
  • Not to be installed upside down
  • Horizontal rotation:ᅠ ᅠfromᅠ ᅠ0°ᅠ ᅠup toᅠ ᅠ360°
  • Horizontal speedᅠ ᅠ(fixed):ᅠ ᅠ6°/s
  • Pan Torque:ᅠ ᅠ2.5kgm
  • Vertical plane movement:ᅠ ᅠfromᅠ ᅠ-90°ᅠ ᅠup toᅠ ᅠ+90°
  • Tilt speedᅠ ᅠ(fixed):ᅠ ᅠ2.4°/s
  • Vertical torque:ᅠ ᅠ6kgm
  • 1x Ex d 3/4” NPT IP66 ATEX cable gland for armoured cable at the base of the P&T
  • Pre-wired multipolar armored cable normally supplied with 7.5m (25ft) length: diameter 21.4mm (0.85in): 21 poles 0.5mm², 6 poles 1.5mm², 2 RG179, 75 Ohm
  • Minimum bending radius:10xᅠ ᅠcable diameter
  • External dimensions:ᅠ ᅠ427.5x571.4x560mm (16.8x322.5x22in)
  • Internal dimensions:ᅠ ᅠ180x380mm (7.1x15in)
  • Internal usable area:ᅠ ᅠ100x100x280mm (3.9x3.9x11in)
  • Unit weight:ᅠ ᅠ56.5kg (124.6lb)
Housing's window
  • Germanium window
  • Usable diameter:ᅠ ᅠ114mm (4.5in)
  • Thick:12mm (0.47in)
  • External treatment:ᅠ ᅠantiscratchᅠ ᅠ(Hard Carbon Coating - DLC),ᅠ ᅠantireflection
  • Internal treatment:ᅠ ᅠantireflection
  • Spectral range:ᅠ ᅠfromᅠ ᅠ7.5μmᅠ ᅠup toᅠ ᅠ14μm
  • Medium transmittanceᅠ ᅠ(fromᅠ ᅠ7.5μmᅠ ᅠup toᅠ ᅠ11.5μm):ᅠ ᅠ86.6%
  • Medium transmittanceᅠ ᅠ(fromᅠ ᅠ11.5μmᅠ ᅠup toᅠ ᅠ14μm):ᅠ ᅠ67.8%
  • Power supply IN 24Vac, 50/60Hz
  • Horizontal and vertical motor consumption: 50W max
  • Standard vertical and horizontal preset potentiometers
  • Heater Ton 10°C±4°C (50°F±7°F) Toff 25°C±3°C (77°F±5°F):
  • IN 24Vac, consumption 20W max
  • Devices to install inside the housing:
  • Camera equipped with lens with max total power of 20W
  • Power supply max 24Vac (only for analog camera)
  • Usable volume for camera/lens:ᅠ ᅠ2800cm³
  • Minimum distance between the walls of the housing and the camera/lens: 12mm
  • For installation indoors and outdoors
  • Operating temperature with heating:ᅠ ᅠfromᅠ ᅠ-20°C (-4°F)ᅠ ᅠup toᅠ ᅠ+50°C (122°F)
  • Always refer to the temperature in the marking.
  • Relative humidity:ᅠ ᅠfromᅠ ᅠ10%ᅠ ᅠup toᅠ ᅠ95%ᅠ ᅠ(no condensation)
  • ATEXᅠ ᅠ(EN 60079-0:2012 +A11:2013, EN 60079-1:2014, EN 60079-31:2014):
  • Exᅠ ᅠII 2G Ex d IIC T6 Gb

    Exᅠ ᅠII 2D Ex t IIIC T85 °C Db IP66

  • EAC EX:
  • Ex II 2G Ex d IIC T6 Gb,-20°C/+50°C

    EX II 2D Ex t IIIC T85°C Db -20°C/+50°C, IP66

  • EXPTS000 Sunshield 580mm (22.8in) for EXPT series
Brackets and adaptors
  • EXPTWB000 Bracket RAL7032 for EXPT series
Related products
  • EXDTRX3 Data telemetry receiver 17 functions, 230Vac
  • EXDTRX324 Data telemetry receiver 17 functions, 24Vac